Led matrix with HT1632C controller (4)

by luca


To display a single character using our font, Arduino has to:


  • read the character
  • substract 33 from its decimal value
  • read, from aipointe_info[] array, character’s length and offset
  • retrieve, from aipointe_font[] font, a number of bytes equal to its length starting from offset position
  • send those bytes to the display


Compared to my previous examples, I added a new function to clear the whole display sending all zeroes:

typedef struct {  
  unsigned char length;  
  unsigned int offset;

The complete sketch is available on GitHub.


I wrote a simple C# program to send on a serial port the characters with decimal value from 33 to 127, one every 250ms:

FONT_INFO aipoint_info[] = {
  {2, 0},	// !
  {5, 2},	// "
  {5, 7},	// #
  {5, 12},	// $
  {5, 17},	// %

Here’s the sketch running:

[youtube id=”TkUTa2aXL9g” width=”600″ height=”350″]

Related Posts


Locomolo Sunday October 14th, 2012 - 12:45 PM

Hi Luca,

I have a 3208 matrix display likes yours, but when i upload the arduino’s sketch all is working well but the text display is rotated 90 degres. It’ s like the leds panels aren’t wired in the same position.

This is my 3208 led matrix:


How can i modify your sketch to getting the correct position?


luca Sunday October 14th, 2012 - 01:12 PM

Hi Luis,

mmm it seems they rotated each matrix 90 degrees? What does it happen if you run the “static text” example (nr 3)? Could you please post a photo?

Locomolo Sunday October 14th, 2012 - 06:59 PM

Hi Luca!

Yes, each matrix is rotated 90 degrees.



luca Tuesday October 16th, 2012 - 04:23 PM

Hi Luis,

mmm I wasn’t able to find any datasheets about your display to know how they connected each matrix to the controller. I’m going to send you a demo sketch via mail to do some tests…

Locomolo Tuesday October 16th, 2012 - 11:25 PM

Hi Luca, here some info about this led matrix( datasheet…)


Thanks a lot, i ‘am ready for testing.

luca Thursday October 18th, 2012 - 09:09 AM

Hi Luis,

could you try to run my first sketch: http://www.lucadentella.it/2012/10/03/matrice-di-led-con-ht1632c-2/ and write down the sequence leds turn on? So we can understand how leds are mapped to RAM cells… thanks!

Locomolo Sunday October 21st, 2012 - 01:25 PM

Hi luca, i upgraded my fileshack library with the images, arduino UNO running your first sketch.

The order is, the first dot begins at the rightest matrix, at bottom right, and the last is the upperest left, always in horizontal direction form the right to the left. Similar for the four matrix.

Check it please

luca Saturday October 27th, 2012 - 09:40 AM

Hi Luis,

I’ve just sent you a demo sketch for your display, let me know how it works

Toni B. Sunday November 4th, 2012 - 02:45 PM

Thanks vor the great help ! I Try the same Projekt but i try to make 2 led Matrix with 8x 32 Leds with 16.000 mcd each red led. I want go give any Text out of my rear from my Car XD such as the German Police .

Great thanks from Germany !

luca Sunday November 4th, 2012 - 10:59 PM

Thanks Toni!

Locomolo Thursday November 15th, 2012 - 09:17 PM

Hi Lucca thanks for your help, finally i found a compatible library in Github, otherwise i keep regarding your project 🙂

luca Friday November 16th, 2012 - 08:48 AM

Good news, Luis!
Could you please send me the link of your library? I’ll add it in my article…

Martin Wednesday September 18th, 2013 - 02:16 PM

Hi Luca,

forgot to tell, yes. I’m using same matrix as Locomolo (mcu 3208 matrix clock, with atmega removed) and chars and scroll direction is rotated 90 degrees.

Searched all over github (and the rest of the internet :)) but can’t find working solution.

luca Thursday September 19th, 2013 - 12:46 PM

Hi Martin,

hope that Locomolo will send you the link to the library he found on Github because I can’t find it too… 🙁

xyz Monday March 18th, 2013 - 11:03 PM


Currently I am working on Sure Electronics 0832 Display interfacing with PIC16F1937.
I am using SPI interface between PIC16F1937 and Display.

I am facing problem with Scrolling Message across Led display. I made 4*7 character library. Every time i am shifting 4 columns in address for displaying next char. but it overlaps.I am starting with R-L shifting but when it goes beyond 0x00 address ,it overlaps with last addresses(0x3E).

Can you please provide some guidelines for scrolling text. in C?

luca Thursday March 21st, 2013 - 09:30 AM

Hello! Give a look to my Arduino code (on Github): it’s in C. If you have any questions about it write me a comment!

Martin Sunday September 15th, 2013 - 12:53 PM


i’m also having the same problem with mcu matrix but can’t find working code on github.
Could you point me in right direction?

tnx, martin

luca Tuesday September 17th, 2013 - 09:07 AM

Hi Martin,

do you mean the same problem as Locomolo?

Doug Thursday February 12th, 2015 - 11:25 AM

Hi Luca,

Has been googling and browsing the internet to no result of getting info about manually trigger character from switches.

Now i found your article which is the closest thing i can find related to my needs and i hope you can give me some light in the darkness.

I just need to output automatic transmission gear position (P R N D 3 2 1 O) to 5×8 led matrix.
The input will be +12v via automatic gear selector/switch (no clock generator or such, just a simple open/close switch).

Could you please help me ?

Thanks in advanced luca.

luca Friday February 13th, 2015 - 09:29 PM

Hi Doug: how do you “know” which gear is selected? Does a single switch corrispond to a specific gear (I mean, do you have 8 switches for 8 gears)? You could monitor the status of each switch using a digital PIN of Arduino and then, with some if display the correct letter on the led matrix


Leave a Reply to Martin Cancel Reply

nine − three =