Tra i tanti service online per la produzione di PCB, mi ha colpito l’offerta di SeeedStudio: aggregando più ordini riescono ad offrire caratteristiche professionali ad un prezzo davvero contenuto.
Ho voluto fare una prova ordinando il pacchetto di 10 PCB, dimensione massima 5x5cm, al costo di 9.90$ + 3.52$ di spedizione – al cambio meno di 10 euro. SeeedStudio non accetta direttamente i files .brd di Eagle, per questo ho pensato di scrivere questa piccola guida con qualche suggerimento su come sfruttare al meglio il servizio Fusion PCB.
Scarichiamo dalla pagina dedicata al servizio Fusion PCB, i due archivi:
- DRU for 2-layer board
- Seeed Gerber Generater 2-layer board
Il primo va decompresso nella sottocartella dru della cartella principale di Eagle, il secondo nella sottocartella cam.
Apriamo ora il nostro progetto in Eagle e visualizziamo la Board; quindi, per verificare che il PCB disegnato soddisfi i requisiti del servizio Fusion PCB, selezioniamo dalla toolbar Drc, quindi clicchiamo Load… e apriamo il file Fusion_eagle_rule_v1.1.dru:
Clicchiamo su Check, se tutto è ok la finestra DRC Errors non conterrà errori; in caso contrario dovremo sistemare il nostro PCB in base agli errori rilevati.
Siamo quindi pronti per esportare i files, dal menu File selezioniamo CAM Processor.
Nella finestra del CAM Processor, apriamo il menu File -> Open -> Job… Selezioniamo il job Seeed_Gerber_Generater_v0r95_DrillAlign.cam:
Clicchiamo sul pulsante Process Job: Eagle produrrà nella cartella del nostro progetto alcuni nuovi files, risultato dell’esportazione.
Prima di inviare tali files a SeeedStudio, vi consiglio di verificarne il contenuto con un editor Gerber: nella mia esperienza mi è infatti capitato alcune volte di trovare errori in fase di esportazione (ad es. se si utilizzano font proporzionali questi potrebbero cambiare dimensione).
Un ottimo software opensource è Gerbv, del quale esiste anche il port per Windows.
Per aprire i files del nostro progetto, selezioniamo File -> Open layer(s)…
Selezioniamo (tenendo premuto il tasto CTRL è possibile selezionare più files contemporaneamente) i 7 files che dovremo inviare a SeeedStudio:
- .GTL (contiene le piste sul lato superiore)
- .GBL (contiene le piste sul lato inferiore)
- .GTS (contiene le stagnature per il lato superiore)
- .GBS (contiene le stagnature per il lato inferiore)
- .GTO (contiene la serigrafia lato superiore)
- .GBO (contiene la serigrafia lato inferiore)
- .TXT (contiene coordinate e dimensioni dei fori)
Visualizzando selettivamente i vari layers possiamo renderci conto se l’esportazione ha avuto successo:
Se tutto è ok, possiamo preparare un archivio ZIP con i files elencati sopra.
Colleghiamoci ora al sito di SeeedStudio, nella sezione relativa al servizio FusionPCB.
Carichiamo lo ZIP creato con l’apposita funzione:
quindi completiamo l’ordine scegliendo quantità e caratteristiche dei PCB; potremo quindi seguirne l’evoluzione direttamente dall’area clienti del sito.
E infine, dopo qualche settimana, arriveranno i PCB!
Molto interessante come notizia, ci sto facendo un pensierino. E grazie per la guida all’ordine.
grazie a te per il feedback!
davvero complimenti!
appena ho qualche momento di libertà vedrò di buttare giù uno schema e proverò il servizio il prima possibile!
p.s. sono arrivato qui da dangerousprototypes con grande piacere
grazie, in effetti da quando DP ha messo il post il grafico delle visite si è impennato 😉
Dogana? Tempi?
tempi di produzione circa 6 giorni (SeeedStudio lavora a batch quindi dipende se sei “fortunato” e invii l’ordine quando stanno per mandarne uno in lavorazione); tempi di spedizione una settimana per arrivare in Italia (tracking su HKPost)… da qui l’enigma delle poste italiane: a me il pacchetto è rimasto fermo in dogana due settimane.
Per quanto riguarda le spese, se l’importo è basso (il mio ordine era da 10 euro) passa esente.
Hi, I work with Target 3001 and have a question about the data files for Seeed Studio. How should the drill file be structured? And on which layer should be the outline, and how does it work when the outline is on the silk layer ?Target 3001 all exported into individual files *.Drill, *.Outline… all other layers looks good.
regards from germany
Hi,
when i do the DRC check, i get a bunch or ‘stop mask’ errors.
i have never seen that before, it seems that the error triggers every time there is a pad and silkscreen at the same place.
Do you have any idea how i would solve that? is it a problem at all?
thanks
Hi!
You’re right, those errors mean that you have a silkscreen on the top of a pad… you can ignore it as it isn’t a problem for Seeed’s service.
I am a KiCAD user, and have not had any issues with any files sent on multiple orders. I do have the option to clip the silkscreen layers when generating Gerber files and have done this on my last two orders and stated on my email with file transmittal. Does this help reduce the pre-fabrication time needed, or do they clip back further than the solder mask?
As requested I also put the order number on the top silkscreen and then put a call-out leader pointing to the location outside of the board edge. Does the call-out help even though the call-out needs to be clipped prior to production?
I am from the school of the design for manufacture-ability and by providing files that are able to go directly into production reduces cost as the board house does not need to perform this task prior to making the screen.
It would be nice to get feed back on these two items if they help reduce pre-processes time and keep costs down.
Hi, i tried my Pcb on Gerbv 2.6.0. I used proportional text font but they look like vector font in Gerbv. So,some texts changed position. I designed my pcb in Eagle. Is it effects like this on real pcb?
Another Question: In cam processor what we choose outut device? Is it GERBER_RS274X ?
Hi peo,
proportional fonts don’t work well with gerber export, you’d better to use vector fonts.
In CAM processor, you have to choose the .cam file provided by Seeeds (Seeed_Gerber_Generater_v0r95_DrillAlign.cam)
Thanks for tutorial…. but not the PCB design example. It is switchmode device ant distance between L and swith MUST be short ant thick. And to the caps. 🙂
Hi,
Very good guide.
CAM process generates more than 7 files you say, should I ignore the rest? (using seed studio cam file)
thank you.
Hi!
Yes, FusionPCB needs only the 7 files listed in my tutorial: you can ignore the other ones.
Hi Luca
I followed your excellent tutorial and submitted my zip file to seed studio however I have just had an email saying that my design doesn’t include drill sizes. The *.TXT file was included in the zip and when I view the drill layer in Gerbv I can see a lot of circles with a forward slash through them as well as a few egg-timer type symbols. Could you tell me where I’m going wrong please?
Thanks
This tutorial is great! Thanks for doing it.
I use Eagle 6.5.0 and gerbv 2.6.1
Is it normal that the dimension lines are on all layers?
Hi Alain, yes.
Grazie per le preziose info Luca, utilissime per chi ha a che fare con seedstudio per la prima volta!
Here’s another cheap PCB service, starting from $9.9, choose the color yourself.
http://www.elecfreaks.com/store/pcb-service-c-39.html
thanks!
Hi Luca & everyone,
This is Shuyang from Seeed fusion.. Thank you for that wonderful guide. I would like to put this link on our website. What do you think?
Please feel free to contact me in shuyang@seeed.cc for any question.
Thanks!
Shuyang
Hi! Of course I’m happy if you link my tutorial on your website! Thanks